This article may contain affiliate links. If you make a purchase after clicking on a link we may earn a small commission at no extra cost to you.

Best Shark Fishing Rods

​Choosing a shark fishing rod will be mostly influenced by how you intend on fishing. 

Will you be offshore on a boat or fishing from the shore on a pier or the beach?

​Depending on your where you will be fishing will probably be the number one influencing factor on what type of shark rod you buy.

Regardless of the type the best shark fishing rods all need a strong backbone, rod blank and butt section not to mention high quality components such as reel seat line guides and tip guide.

​On a cheap rod the first thing to go is usually either the line guides or the reel seat, it is rarely the rod blank that will fail first.

​Regardless of the type of rod you choose it should be rated as a 50 lb class rod at a minimum.

Sharks need a rod that is capable of handling sustained pressure and can run heavy mono or braid at a minimum of 50 lbs breaking strain.

Ideally you will have enough power in the rod so that the fight does not go on for too long, as in most states for the majority of shark species the fishing is catch and release only.

The quicker you can unhook them the better their chances of surviving when released.

​Shark Fishing Rods for Surf Fishing

Traditional surf fishing has changed considerably in the last ten years especially for larger species like shark.

A lot of anglers are now using either a kayak or more recently drones to haul their large shark baits out past the breaking surf some as far as several hundred feet beyond it.

This approach no longer requires a long surf casting rod. Instead they can opt to use slightly longer offshore conventional rods as no casting is required.

​However, if you are just starting out then a surf casting rod will be the best option.

You can run either a spinning or a conventional as your choice of shark fishing reel on these big rods, but more often than not when fishing for sharks less than six feet spinning tackle is the more popular.

​A longer surf casting rod for shark fishing gives has a number of advantages over a shorter rod:

  • Better casting distance
  • Keeps line high out of the waves
  • Will be easier to detect a bite

Line guides should be ring guides only so you can use either mono or braid. Leave the roller guides to the heavier offshore shark poles.

​Shark Fishing Rods for Offshore Fishing

A good offshore rod for shark will be a convention boat rod 5'6 to 6 feet with a moderate to fast taper the type that is commonly used with a harness. 

You can choose either traditional ring guides or roller guides.

It is generally considered a bad idea to pair roller guides with braid as your main line because if the line slips the roller on to the side the roller will destroy the braid.

Monofilament is a lot more forgiving when used with rollers, the only downside is a little more stretch in your line making hook sets a little less sharper.

Some prefer a fast taper others a more moderate and this is normally a personal preference thing.

​Best Shark Fishing Rods

​1. PENN Carnage II Surf Casting Rod

2. ​​Tsunami Airwave

3. Ugly Stik Tiger Elite

4. St Croix Mojo Surf 

​5. Shimano Tallus

​6. Penn Rampage Conventional Roller

​7. Shimano TLD A Stand Up

​8. Fiblink OffShore Heavy

​Shark Fishing Rods

​As we discussed above your choice of fishing rod for sharks will be determined by whether you are fishing from a boat or from the beach/pier.

All rod for shark fishing need to be well built with a lot of power through the rod blank and down into the butt section. 

You also need to make sure that the reel seat and the line guides or rollers are of the highest quality to help reduce any friction between the line and the guides.

Shark fishing gear should last years of use and abuse if you buy quality from the beginning.

​Surf Shark Rods

Assuming you are actually casting your bait out and not using a kayak to haul it out over the breaking surf then a long surf rod with a heavy power rating usually in the 50 to 80 lbs range is the best rod for the job.

​Length

Personally I would not use a shark fishing pole for this type of fishing under ten feet in length.

A longer ​pole that is eleven or twelve feet long will have a number of advantages over a shorter rod.

A long rod once set into the rod holder will hold your line up high in the air above the crashing waves.

​This also keeps the line high in the water off of the ocean floor free from any snags and also giving you a lot more feedback through the line.

You will also gain a notable amount of distance when casting. A longer rod is basically a much bigger lever and once you load the rod blank that lever becomes a huge spring that will help to whip a large bait and weight a lot further than any short rod can.

​Action

Rod action describes where on the rod blank the rod will start to bend naturally once you apply some pressure to it.

A fast action will bend higher up the blank towards the tip.

What rod action for surf casting for sharks ?

A fast rod action is best when surf fishing for sharks from the beach or a pier. This is will give you the best casting characteristics but also a more sensitive tip for detecting bites.

​Power

Given their size a heavy rod action is a must for all shark fishing. Look for rods that are rated from 50 to 80 lbs.

Anything smaller and although you may end up landing the shark chances are it will take a long time and a tired shark has a lot lower chance of surviving once released than one that is played quickly.

​Offshore Shark Rods

​Size

On a boat shorter is nearly always better so look for a good conventional offshore boat rod in that is either 5'5" or 6' in length.

A shorter rod give you a lot more leverage against a heavy shark and combined with a high torque reel(low gearing) you should be able to exert enough pressure to reel them in quickly.

Short poles are also a lot easier to use on a boat than a long rod unless you are trolling and running a lot of planer boars out wide.

Ring Guides vs Rollers ?

Roller assembly braid mono in rings no chaff

​The main advantage that roller guides give you on big game rods is that they reduce the amount of friction between the line and the guide.

​But if your line pops off onto the side of the roller it can make bits of your line especially if you are using braid.

Monofilament is the better option if you opt for a ​pole with roller guides.

​Modern ring guides especially the higher end ones are so hard now that they will wear very little and cause very little friction against the line.

There is very little to go wrong with a simple ring guide assuming it is of a decent quality.

You do see a lot of anglers that use a roller guide on the tip and then ring guides on the rest of the rod but in my opinion this is a mistake. 

You should either go all roller guides or all ring guides no mixing and matching as once you use one of the other type you loose the benefits of the type of guide.

​Bent Butt or Straight ?

If you are new to offshore fishing then you may never have encountered a bent butt rod before.

These rods are for using in a fighting chair. One thing to remember that this kind of setup if not tournament legal and so if you intend on doing some tournaments then a straight butt rod is the way to go.

Straight butt rods can be used in a belt or harness.

A really high end expensive rods the butt will be solid aluminum and they can be flicked from the straight position into a bent but as there is a pivot point just below the reel seat.

​Materials

Fiberglas or some form of modern fiberglass blend with either graphite or carbon fiber but straight up fiberglass is a pretty solid bet.

The standard of epoxy resin will also have an impact of the final quality of the rod.